Jump to content

Expanding nozzle

From Wikipedia, the free encyclopedia
The XLR-129 featured an expanding nozzle. The extension is almost cylindrical compared to the inner section.

The expanding nozzle is a type of rocket nozzle that, unlike traditional designs, maintains its efficiency at a wide range of altitudes. It is a member of the class of altitude compensating nozzles, a class that also includes the plug nozzle and aerospike. While the expanding nozzle is the least technically advanced and simplest to understand from a modeling point of view, it also appears to be the most difficult design to build.

In the traditional bell nozzle the engine skirt is shaped to gradually flare out from the small-diameter exit from the combustion chamber, growing larger further from the chamber. The basic idea is to lower the pressure of the exhaust by expanding it in the nozzle, until it reaches ambient air pressure at the exit. For operations at sea level the skirt is generally short and highly angled, at least in comparison to a skirt designed for operations in space, which are longer and more gradually shaped. This means that a rocket engine that spends any significant amount of time climbing through the atmosphere cannot be optimally shaped; as it climbs the ambient pressure changes, so the exact shape and length of the skirt would have to change in order to maintain the proper pressure. Rocket designers have to select the sweet spot that is most appropriate to their needs, realizing that this will reduce thrust by as much as 30% at other altitudes.

The expanding nozzle addresses this to a degree by including two skirts on a single engine, one inside the other. The first skirt, attached directly to the combustion chamber, is designed for use at lower altitudes and is short and squat. The second, sitting outside the first, fits over the lower altitude bell to extend it into a longer and narrower (measured in terms of length) bell used for higher altitudes. At liftoff the outer bell is pulled up from the inner bell, out of the way of the exhaust. As the spacecraft climbs, the outer bell is pushed back down over the inner bell to increase the thrust efficiency. Thus an expanding nozzle can have two sweet spots, which can lead to a major improvement in overall performance.

Generally simple in concept, the expanding nozzle is considerably more complex to build than it might seem. Engine bells must be cooled to avoid damage from the hot rocket exhaust, and this has presented problems in expanding nozzle designs. The cooling is normally accomplished by running either the oxidizer or fuel (in the case of LH2 fueled engines) through tubing in the bell. With the bell moving, plumbing carrying the coolant to the bell has to be flexible and this increases complexity to the extent that the advantages of the design are often considered too costly. In the case of liquid hydrogen, the fluid also has the disadvantage of being highly reactive chemically, making a variety of common flexible materials unsuitable for use in this role.

For the aforementioned reasons modern designs (e. g. NK-33-1, RL-10A-4, and RL-10B-2) feature radiatively cooled reinforced carbon–carbon nozzle extensions needing no coolant plumbing at all.

The first engine design to include an expanding nozzle appears to be the Pratt & Whitney XLR-129. The XLR-129 was intended to power a McDonnell Aircraft boost-glide aircraft design that was entered as part of the Project ISINGLASS (or RHEINBERRY) study looking at follow-on designs to replace the Lockheed A-12 that was just entering service. It was a liquid oxygen/liquid hydrogen design that used staged combustion and generated about 250,000 lbf (1,100 kN) thrust. An enlarged version of the XLR-129 was proposed for the Space Shuttle Main Engine contest, but this was won by the RS-25, an enlarged Rocketdyne HG-3. Since these engines are fired from the point of liftoff into extra-atmospheric space flight, any sort of altitude compensation could dramatically improve their overall performance. The expanding nozzle was later abandoned in a cost-cutting phase, and the RS-25 suffers a 25% loss of performance at low altitude as a result.[1]

Glushko has used an expanding nozzle on one design, the RD-701 tripropellant rocket. Funding ran out with the fall of the Soviet state, but the designers are convinced the engine has potential and have approached several parties for additional funding.

See also

[edit]

References

[edit]
  1. ^ "Pratt & Whitney GTF™ Engine MRO Network Expanding to Eight Engine Centers by 2020". www.epicos.com. Retrieved 2022-06-08.
[edit]