Jump to content

Tube socket

From Wikipedia, the free encyclopedia
Left to right: octal (top and bottom view), loctal, and miniature (top and side view) sockets. An early transistor socket and an integrated circuit socket are included for comparison.

Tube sockets are electrical sockets into which vacuum tubes (electronic valves) can be plugged, holding them in place and providing terminals, which can be soldered into the circuit, for each of the pins. Sockets are designed to allow tubes to be inserted in only one orientation. They were used in most tube electronic equipment to allow easy removal and replacement. When tube equipment was common, retailers such as drug stores had vacuum tube testers, and sold replacement tubes. Some Nixie tubes were also designed to use sockets.

Throughout the tube era, as technology developed, sometimes differently in different parts of the world, many tube bases and sockets came into use.[1][2] Sockets are not universal; different tubes may fit mechanically into the same socket, though they may not work properly and possibly become damaged.

Tube sockets were typically mounted in holes on a sheet metal chassis and wires or other components were hand soldered to lugs on the underside of the socket. In the 1950s, printed circuit boards were introduced and tube sockets were developed whose contacts could be soldered directly to the printed wiring tracks. Looking at the bottom of a socket, or, equivalently, a tube from its bottom, the pins were numbered clockwise, starting at an index notch or gap, a convention that has persisted into the integrated circuit era.

In the 1930s, tubes often had the connection to the control grid brought out through a metal top cap on the top of the tube. This was connected by using a clip with an attached wire lead. An example would be the 6A7 pentagrid converter. Later, some tubes, particularly those used as radio frequency (RF) power amplifiers or horizontal deflection amplifiers in TV sets, such as the 6DQ6, had the plate or anode lead protrude through the envelope. In both cases this allowed the tube's output circuitry to be isolated from the input (grid) circuit more effectively. In the case of the tubes with the plate brought out to a cap, this also allowed the plate to run at higher voltages (over 26,000 volts in the case of rectifiers for color television, such as the 3A3, as well as high-voltage regulator tubes.) A few unusual tubes had caps for both grid and plate; the caps were symmetrically placed, with divergent axes.

Tube 75 from the 1930s with UX-6 base and top grid cap

The first tubes

[edit]

The earliest tubes, like the Deforest Spherical Audion[3] from c. 1911, used the typical light bulb Edison socket for the heater, and flying leads for the other elements. Other tubes directly used flying leads for all of their contacts, like the Cunningham AudioTron from 1915,[4] or the Deforest Oscillion.[5] Type C6A xenon thyratrons, used in servos for the U.S. Navy Stable Element Mark 6, had a mogul screw base and L-shaped stiff wires at the top for grid and anode connections.[6] Mating connectors were machined pairs of brass blocks with clamping screws, attached to flying leads (free hanging).

Early bases

[edit]
Two early tubes with four- and six-pin bases

When tubes became more widespread, and new electrodes were added, more connections were required. Specially designed bases were created to account for this need. However, as the world was suffering from World War I, and the new electronics technology was just emerging, designs were far from being standardized. Usually, each company had their own tubes and sockets, which were not interchangeable with tubes from other companies. By the early 1920s, this situation was finally changing, and several standard bases were created. They consisted of a base (ceramic, metal, bakelite, etc.) with a number of prongs ranging from three to seven, with either a non-regular distribution or with one or two of the prongs of bigger diameter than the other, so that the tube could only be inserted in a certain position. Sometimes they relied on a bayonet on the side of the base. Examples of these are the very common USA bases UX4, UV4, UY5 and UX6, and the European B5, B6, B7, B8, C7, G8A, etc. Tubes in the USA typically had from four to seven pins in a circular array, with adjacent pairs of larger pins for heater connections.

Before alternating current (AC) line/mains-powered radios were developed, some four-pin tubes (in particular, the very common UX-201A ('01A)) had a bayonet pin on the side of a cylindrical base. The socket used that pin for retaining the tube; insertion finished with a slight clockwise turn. Leaf springs, essentially all in the same plane, pressed upward on the bottoms of the pins, also keeping the bayonet pin engaged.

The first hot-cathode CRT, the Western Electric 224-B, had a standard four-pin bayonet base, and the bayonet pin was a live connection. (Five effective pins: It was an electrostatic-deflection gas-focused type, with a diode gun and single-ended deflection. The anode and the other two plates were common.)

An early exception to these types of bases is the Peanut 215, which instead of using prongs had a tiny bayonet base with four drop-like contacts. Another exception is the European Side Contact series commonly known as P, which instead of using a prong, relied on side contacts at 90 degrees from the tube axis with four to twelve contacts.

Octal

[edit]
Because of the ubiquity of the octal socket, many other components used it for their pin configuration including relays (not shown), vibrators (top), crystal oscillators (bottom) and small-signal transformers (not shown)

In April 1935, the General Electric Company introduced a new eight-pin tube base with their new metal envelope tubes.[7][8] The new base became known as the octal base.[9] The octal base provided one more conductor with a smaller overall size of the base than the previous line of U. S. tube bases which had provided a maximum of seven conductors. Octal bases, as defined in IEC 60067,[10] diagram IEC 67-I-5a, have a 45-degree angle between pins, which form a 17.45 mm (1116 in) diameter circle around a 7.82 mm (516 in) diameter keyed post (sometimes called a spigot) in the center. Octal sockets were designed to accept octal tubes, the rib in the keyed post fitting an indexing slot in the socket so the tube could only be inserted in one orientation.

When used on metal tubes, pin 1 was always reserved for a connection to the metal shell, which was usually grounded for shielding purposes. This reservation prevented tubes such as the 6SL7/6SN7 dual triodes from being issued with metal envelopes, as such valves need three connections (cathode, grid, anode) for each triode (making six total) plus two connections for the paralleled heaters. The octal base soon caught on for glass tubes, where the large central post could also house and protect the "evacuation tip" of the glass tube. The eight available pins allowed more complex tubes than before, such as dual triodes, to be constructed. The glass envelope of an octal base tube was cemented into a bakelite or plastic base with a hollow post in the center, surrounded by eight metal pins. The wire leads from the tube were soldered into the pins, and the evacuation tip was protected inside the post.

Matching plugs were also manufactured that let tube sockets be used as eight-pin electrical connectors; bases from discarded tubes could be salvaged for this purpose. Octal sockets were used to mount other components, particularly electrolytic capacitor assemblies[11] and electrical relays; octal-mount relays are still common.[12]

Most octal tubes following the widespread European designation system have penultimate digit "3" as in ECC34 (full details in the Mullard–Philips tube designation article). There is a different, totally obsolete, pre-world-war-II German octal type.[citation needed]

Octal and miniature tubes are still in use in tube-type audio hi-fi and guitar amplifiers. Relays were historically manufactured in a vacuum tube form,[13] and industrial-grade relays continue to use the octal base for their pinout.[14][15]

Loctal

[edit]
A loctal-base tube, Polish Telam UCH21 next to a wooden match for size comparison

A variant of the octal base, the B8G loctal base or lock-in base (sometimes spelled "loktal" — trademarked by Sylvania), was developed by Sylvania for ruggedized applications such as automobile radios. Along with B8B (a British designation out of date by 1958), these eight-pin locking bases are almost identical and the names usually taken as interchangeable (although there are some minor differences in specifications, such as spigot material and spigot taper, etc.).[16] The pin geometry was the same as for octal, but the pins were thinner (although they will fit into a standard octal socket, they wobble and do not make good contact), the base shell was made of aluminium, and the center hole had an electrical contact that also mechanically locked (hence "loctal") the tube in place. Loctal tubes were only used widely by a few equipment manufacturers, most notably Philco, which used the tubes in many table radios. Loctal tubes have a small indexing mark on the side of the base skirt; they do not release easily from their sockets unless pushed from that side. Because the pins are actually the Fernico or Cunife lead-out wires from the tube, they are prone to intermittent connections caused by the build-up of electrolytic corrosion products due to the pin being of a different metallic composition to the socket contact.

The loctal tube's structure was supported directly by the connecting pins passing through the glass "button" base. Octal tube structures were supported on a glass "pinch", formed by heating the bottom of the envelope to fusing temperature, then squeezing the pinch closed. Sealing the pinch embedded the connecting wires in the pinch's glass and gave a vacuum-tight seal. The connecting wires then passed through the hollow base pins, where they were soldered to make permanent connections.

Loctal tubes had shorter connecting lengths between the socket pins and the internal elements than did their octal counterparts. This allowed them to operate at higher frequencies than octal tubes. The advent of miniature "all-glass" seven- and nine-pin tubes overtook both octals and loctals, so the loctal's higher-frequency potential was never fully exploited.

Loctal tube type numbers in the USA typically begin with "7" (for 6.3-volt types) or "14" for 12.6-volt types. This was fudged by specifying the heater voltage as nominally 7 or 14 volts so that the tube nomenclature fitted.[17] Battery types (mostly 1.4-volt) are coded "1Lxn", where x is a letter and "n" a number, such as "1LA4". Russian loctals end in L, e.g. 6J1L. European designations are ambiguous; all B8G loctals have numbers either in the range:

  • 20–29, (such as EBL21, ECH21, EF22) except for early tubes in the series: DAC21, DBC21, DCH21, DF21, DF22, DL21, DLL21, DM21 which have either B9G or octal bases, the change to Sylvania's locktal standard coming in 1942[18]
  • or 50–59 (special bases, including the European 9-pin lock-in base), but other types are in the same range (e.g. while EF51 is B8G loctal, the EF55 is 9-pin loctal, B9G, and the EL51 has a side-contact P8A base).

Other loctals

[edit]
  • Nine-pin loctal bases, B9G, include the 1938 Philips EF50, EL60 and some type numbers in the European 20–29 and 50–59 range;
  • There is a different "loctal Lorenz" in the Mullard–Philips tube designation .

Miniature tubes

[edit]
A pair of 12AU7As (ECC82) showing both triodes.

Efforts to introduce small tubes into the marketplace date from the 1920s, when experimenters and hobbyists made radios with so-called peanut tubes[19] like the Peanut 215 mentioned above. Because of the primitive manufacturing techniques of the time, these tubes were too unreliable for commercial use.

RCA announced new miniature tubes in Electronics magazine, which proved reliable. The first ones, such as the 6J6 ECC91 VHF dual triode, were introduced in 1939. The bases commonly referred to as "miniature" are the seven-pin B7G type, and the slightly later nine-pin B9A (Noval). The pins are arranged evenly in a circle of eight or ten evenly spaced positions, with one pin omitted; this allows the tube to be inserted in only one orientation. Keying by omitting a pin is also used in 8- (subminiature), 10-, and 12-pin (Compactron) tubes (a variant 10-pin form, "Noval+1", is basically a nine-pin socket with an added center contact).

As with loctal tubes, the pins of miniature tube are stiff wires protruding through the bottom of the glass envelope which plug directly into the socket. However, unlike all their predecessors, miniature tubes are not fitted with separate bases; the base is an integral part of the glass envelope. The pinched-off air evacuation nub is at the top of the tube, giving it its distinctive appearance. More than one functional section can be included in a single envelope; a dual triode configuration is particularly common. Seven- and nine-pin tubes were common, though miniature tubes with more pins, such as the Compactron series, were later introduced, and could fit up to three amplifying elements. Some miniature tube sockets had a skirt that mated with a cylindrical metal electrostatic shield that surrounded the tube, fitted with a spring to hold the tube in place if the equipment was subject to vibration. Sometimes the shield was also fitted with thermal contacts to transfer heat from the glass envelope to the shield and act as a heat sink, which was considered to improve tube life in higher power applications.

Electrolytic effects from the differing metal alloys used for the miniature tube pins (usually Cunife or Fernico) and the tube base could cause intermittent contact due to local corrosion, especially in relatively low current tubes, such as were used in battery-operated radio sets. Malfunctioning equipment with miniature tubes can sometimes be brought back to life by removing and reinserting the tubes, disturbing the insulating layer of corrosion.

Miniature tubes were widely manufactured for military use during World War II,[20] and also used in consumer equipment. The Sonora Radio and Television Corporation produced the first radio using these miniature tubes, the "Candid", in April 1940.[21] In June 1940 RCA released its battery-operated Model BP-10, the first superheterodyne receiver small enough to fit in a handbag or coat pocket.[22][23] This model had the following tube lineup: 1R5 — pentagrid converter; 1T4 — I.F. amplifier; 1S5 — Detector/AVC/AF Amplifier; 1S4 — Audio Output. The BP-10 proved so popular that Zenith, Motorola, Emerson, and other radio manufacturers produced similar pocket radios based on RCA's miniature tubes.[21] Several of these pocket radios were introduced in 1941 and sold until the suspension of radio production in April 1942 for the duration of World War II.[24]

After the war miniature tubes continued to be manufactured for civilian use, regardless of any technical advantage, as they were cheaper than octals and loctals.[20]

Miniature seven-pin base

[edit]

The B7G (or "small-button" or "heptal") seven-pin miniature tubes are smaller than Noval, with seven pins arranged at 45-degree spacing in a 9.53 mm (3/8th inch) diameter arc, the "missing" pin position being used to position the tube in its socket (unlike octal, loctal and rimlock sockets). Examples include the 6AQ5/EL90 and 6BE6/EK90. European tubes of this type have numbers 90-99, 100-109, 190-199, 900-999. A few in the 100-109 series have unusual, non-B7G bases, e.g., Wehrmacht base.

Noval base

[edit]

The nine-pin miniature Noval B9A base, sometimes called button 9-pin, B9-1, offered a useful reduction in physical size compared to previous common types, such as octal (especially important in TV receivers where space was limited), while also providing a sufficient number of connections (unlike B7G) to allow effectively unrestricted access to all the electrodes, even of relatively complex tubes such as double triodes and triode-hexodes. It could also provide multiple connections to an electrode of a simpler device where useful, as in the four connections to the grid of a conventional grounded-grid UHF triode, e.g., 6AM4, to minimise the deleterious effects of lead inductance on the high-frequency performance.

This base type was used by many of the United States and most of the European tubes, e.g., 12AX7-ECC83, EF86 and EL84, produced commercially towards the end of the era before transistors largely displaced their use.

The IEC 67-I-12a specification calls for a 36-degree angle between the nine pins of 1.016 mm thickness, in an arc of diameter 11.89 mm.

European tubes of this type have numbers 80-89, 180-189, 280-289, 800-899, 8000-8999.

Duodecar base

[edit]

The Duodecar B12C base (IEC 67-I-17a) has 12 pins in a 19.1 mm diameter circle and dates from 1961. It was also called the Compactron T-9 construction/E12-70 base[25] It is generally similar in form to a Noval socket, but larger. In the center is a clearance hole for a tube evacuation pip, which is typically on the bottom of a Compactron tube. (It should not be confused with the similar-sounding but differently sized Duodecal B12A base.)

Rimlock base

[edit]

The Rimlock (B8A) base is an eight-pin design with a pin circle diameter close to Noval, and uses a nub on the side of the envelope to engage with a guide and retaining spring in the socket wall. This provides pin registration (since the pins are equi-spaced) and also a fair degree of retention. Early tubes with this base type typically had a metal skirt around the lower ~15mm of the envelope to match the socket wall, and this offered a degree of built-in screening, but these were fairly soon replaced by "skirtless" versions, which had a characteristic widening in the glass to compensate physically for the absence of the skirt. In the European naming scheme, rimlock tubes are numbered in the ranges 40-49, 110-119 (with exceptions), and 400-499, e.g., EF40. Although virtually unknown elsewhere, this was a very common base type in European radios of the late 1940s through the 1950s, but was eventually displaced by the ubiquitous B7G and Noval (B9A) base types.

UHF tubes

[edit]
A box of Acorn sockets.

By 1935 new tube technologies were required for the development of radar and telecommunications. UHF requirements severely limited the existing tubes, so radical ideas were implemented which affected how these tubes connected to the host system. Two new bases appeared, the acorn tube and the lighthouse tube, both solving the same problems but with different approaches. Thompson, G.M. Rose, Saltzberg and Burnside from RCA created the acorn tube by using far smaller electrodes, with radial short connections.[26] A different approach was taken by the designers of the lighthouse tube, such as the octal-base 2C43,[27] which relied on using concentric cylindrical metal contacts in connections that minimized inductance, thus allowing a much higher frequency.

Nuvistors were very small, reducing stray capacitances and lead inductances. The base and socket were so compact that they were widely used in UHF TV tuners. They could also be used in small-signal applications at lower frequencies, as in the Ampex MR-70, a costly studio tape recorder whose entire electronics section was based on nuvistors.

Other socket styles

[edit]

There are many other socket types, of which a few are:

  • Decal B10B base (IEC 67-I-41a) 10 pins with 1.02 mm diameter in an 11.89 mm diameter circle, e.g. PFL200
  • Decar B10G base (IEC E10-73) A 10th pin added to the center of a standard 9-pin miniature base, e.g. 6C9
  • Magnoval B9D base (IEC 67-I-36a) 9 pins with 1.27 mm diameter in a 17.45 mm pin circle diameter arc, e.g. EL503, EL509, PD500, etc. - not to be confused with...
  • Novar B9E base, 9 pins with 1.02 mm diameter in a 17.45 mm pin circle diameter arc, one of several Compactron types, which looks similar to Magnoval (but a Novar tube in a Magnoval socket will not make good pin contact, and a Magnoval tube in a Novar socket may damage the socket).
  • Sub-Magnal B11A base (American), 11-pins. Also used as industrial relay socket and HV power supplies. Amphenol / WirePro (WPI) / Eaton 78-series, Socket (female) part number: 78-S-11. Matching Plug (male) is part number: 86-CP-11
  • Neo Eightar base (IEC 67-I-31a) 8 pins in a 15.24 mm diameter circle
  • 5-pin sub-miniature wire-ended B5A base (no socket used; e.g. EA76)

A remarkably wide variety of tube and similar sockets is listed and described, with some informal application notes, at a commercial site, Pacific T.V.,[28] including nuvistor, eight-pin subminiature, vidicon, reflex klystron, nine-pin octal-like, 10-pin miniature (two types), 11-pin sub-magnal, diheptal 14-pin, and many display tubes such as Nixies and vacuum fluorescent types (and even more). As well, each socket has a link to a clear, high-quality picture.

Some subminiature tubes with flexible wire leads all exiting in the same plane were connected by subminiature inline sockets.

Some low-power reflex klystrons such as the 2K25 and 2K45 had small-diameter rigid coaxial outputs parallel to octal base pins. To accommodate the coax, one contact was replaced by a clearance hole.

Vacuum tubes for high-power applications often required custom socket designs. A jumbo four-prong socket was used for various industrial tubes. A specialized seven-pin socket (Septar or B7A), with all pins in a circle with one pin wider than the others, was used for transmitting tubes. Subminiature tubes with long wire leads, introduced in the 1950s, were often soldered directly to printed circuit boards. Sockets were made for early transistors, but quickly fell out of favor as transistor reliability became established. This also happened with early integrated circuits; IC sockets later became used only for devices that may need to be upgraded.

Summary of base details

[edit]

[29][30]

Common Name Standard Name Other names Base Pins Pin Layout Pin thickness Specification Period Examples European / Pro Electron numeric range
Pee-Wee B3A US Pee Wee 3p 3 08.7mm triangle with pins 1&3 closest[31] 2.36mm[32] 1937 - ZA1004 -
Mazda subminiature B3G[33] European special all-glass miniature 3 (+top) 06.0mm line with 3mm spacing 1mm Mazda 1937 - D1, EA50[34] -
European 3-pin H3A British 3-pin, Eu-3
(or B4, ignoring pin 4)
3 16mm isosceles triangle, greatest distance between pins 2 & 3 3.2mm 1920s to early 1930s
(superseded by Octal and P8)
RE4120, 1832[35] -
UV4 B4B WD-4-Pin 4 09.8mm rectangle with large pin 2 (usually anode) 2.3mm x3
3.1mm (pin 2)
1914 - 1920's
(superseded by UX4)
WD-11 -
UX4 U4A American 4-pin base with or without bayonet pin 4 11.9mm rectangle with thicker pins 1 & 4.
Superseded the UV4 base
3.2mm (pins 2&3)
4.0mm (pins 1&4)
A4-10 1920s - 1930s
(mostly superseded by Octal, but still used for some currently produced directly heated triodes)
A-P Oscillator (1920),[36] 2A3, 300B, B405, X99, WW313A (1938), 866A -
B4 A4A British 4-pin, A4, European 4-pin 4 16.25mm kite 3.2mm 1915[37] to early 1930s
(superseded by Octal and P8)
B405, BL2, R-type -
UY5
UX5
U5A
B5C
US 5-contact
American Small 5-pin, USS5
5 19mm (3/4") circle,
3x60° between pins 1,2 and 4,5,1,
2x90° between pins 2,3,4
3.? A5-11 1920s UY227, 2E22, 1D4, 49, 807 -
B5 O5A British 5-pin, European 5 -pin, Europa 5 16.25mm kite; B4 with central 5th pin added
a B5 socket will accept European 3-pin (H3A) and 4-pin (A4A) tubes
3.2mm 1928[38] to early 1930s
(superseded by Octal and P8)
B443 -
UX6[39] U6A US 6-pin 6 19mm (3/4") circle,
6x60°
3.2mm x4, 3.9mm (pins 1 & 6) 1930's
(superseded by Octal)
1F6, 2A5 -
B7 M7A British 7-pin 7 23.1mm x 18.2mm oval[40] 3.2mm 1930s (ultimately superseded by Octal) AC3/Pen, TDD4, AL60, 18013 -
UX7 U7A US 7-pin small 7 19mm (3/4") circle,
3x52°,4x51°
3.2mm x5,
3.9mm (pins 1&7)
1930's
(superseded by Octal)
2B7, 6A7 -
Septar B7A 7 26mm circle 2.7mm x6, 4.0mm 6C33, 829B, 3C33, 3E29, 832A, 5894, FU-29, GZ67-C
Miniature 7-Pin B7G Miniature, Button, Mi-7 7 09.53mm (3/8") circle,
6x45° then 90° between pins 7 & 1
1.016mm IEC 67-I-10a 1939 - present 1S4/DL91, 6AQ5, 6X4 90-99, some 100-109, 190-199, 900-999
Transcontinental P8A P-Type, Ct8, Philips 8, Side-contact 8 8 29.5mm circle of side-contact pins,
3x30° (pins 1-4),
5x54°
Side-contact Philips 1930s AL3 1-9 usually
Octal K8A[41] IO, International Octal, A08, American octal base, Oc-8 8 17.45mm (11/16") circle, equal 45° spacing, 7.8mm spigot 2.36mm originally: RCA
IEC 67-I-5a
1935 - present 6CA7/EL34, 6L6/5881, 6SN7, 6V6GT, KT63/KT66/KT77/KT88/KT90, 6550, 7591 3G, 30-39, 300-399
Mazda Octal[42] K8B MO8, Octal-8 GB, MO[42] 8 18.5mm circle, 55,5° between pin 1 and 8, 43,5° between the other pins,[43] 8.7mm spigot 2.36mm Mazda 1938 - ?
(short-lived)
ARP12, AR8, SP42, ATP4 [43] -
Loctal B8G[44]
or B8B[45]
8-pin Loktal, Lo-8, Locking Octal 8 17.45mm (11/16") circle, equal 45° spacing, 6.7mm spigot 1.3mm Sylvania 1939 1LN5, EF22, ECH71 20-29 and some others
Rimlock B8A European 8-pin Miniature base, Ri-8 8 11.5mm (0.453") circle, 45° 1.015mm IEC 67-I-11b 1940s
quickly edged-out by Noval, etc
6CU7/ECH42,EL41 40-49
Loctal-9pin B9G[46] 9-pin Loctal, Lo-9 9 21.0mm (13/16") circle, equal 40° spacing,
spigot connected to can
1.3mm Philips 1938[47]
announced Sept. 1938 and available to Pye; general availability early 1939.[48]
EC52 EF50 EF54 EL60 50-60 with some exceptions
Noval (Miniature 9-pin) B9A American Small Button, Button 9-pin 9 11.89mm (15/32") circle,
8x36° then 72° spacing between pins 9 & 1
1.016mm IEC 67-I-12a
JEDEC E9-1
1948 - present (still very popular) 12AX7/ECC83, 6BQ5/EL84 80-89, 180-189, 800-899
Magnoval B9D 9 17.45mm (11/16") circle,
8x36° then 72° spacing between pins 9 & 1
1.27mm IEC 67-I-36a
JEDEC E9-23
1960s-1970s
died out when TVs went fully solid-state
E55L, ED500, PL504 500-599
Novar B9E 9-pin compactron 9 17.45mm (11/16") circle, 9x36° then gap between pins 9 & 1
Note: Novar sockets can be damaged by inserting Magnoval tubes[49]
1.02mm JEDEC E9-65
JEDEC E9-89
1959 -
limited use; mainly TV horiz. output, damper
6JF6, 22JG6A, 7868 -
Decal B10B[50]
or B10C?[51] often incorrectly stated
Dekal 10 11.89mm (15/32") circle,
9x34° then 54° gap between pins 10 & 1
1.016mm IEC 67-I-41a
JEDEC E10-61
1960s - 1970s PFL200, ECC2000, ECH200, PCF201 200-299
2000
Decar B10G Dekar 10 11.89mm (15/32") circle as Noval, with additional center pin 1.016mm Sylvania
JEDEC E10-73
Mid-Late 1960s 6C9, 17C9
Y10A G10A (G8A tubes fit with pins 6 & 10 unused) 10 28mm circle, 2 groups of 5 pins with two gaps AZ11, EC156
Sub-Magnal B11A Magnal, B11 11 17.45mm (11/16") circle as Octal 1.27mm RCA? 1940s to present
DuoDecal B12A Duodekal, B12 12 27mm (1.063") circle,
30° angles
2.36mm B12-43 1950s - 1970s DG7-31, E1T, MW61-80 -
Duodecar B12C 12-Pin-Compactron, E12-70, E12-74 12 19.1mm (3/4") circle,
11x 27.7° then gap between pins 12 & 1
1.02mm E12-70(T9)
E12-74(T12)[52]
1960s - 1970s 1BY2, 6BD11, 12BT3 -
Nuvistor E5-65 5 only pins 2, 4, 8 10, 12 used from Twelvar <1mm E5-65 8393
Nuvistor B12K Twelvar E7-83, E12-64, E12-65 12 11.2mm circular envelope with mixed-spacing field of pins <1mm IEC 67-I-17a
JEDEC E12-64(5/12)
1959 - 7586, 6DV4, 6DV8, 13CW4[53] -

References

[edit]
  1. ^ Qvigstad, Just N. (2012). "Sokkel oversikt radiorør". Vacuum tube bases overview (in Norwegian). Radio amateur LA9DL. Retrieved 9 January 2013.
  2. ^ "Tube Bases". Frank's Electron Tube Pages. Retrieved 20 July 2013.
  3. ^ Stone, Howard. "Deforest Spherical Audion". Stone Vintage Radio Museum. Retrieved 20 July 2013.
  4. ^ Stone, Howard. "Cunningham Tubular Audio Tron". Stone Vintage Radio Museum. Retrieved 20 July 2013.
  5. ^ Stone, Howard. "Deforest Oscillion 250 W Transmitting Tube". Stone Vintage Radio Museum. Retrieved 20 July 2013.
  6. ^ "C6A". Radiomuseum.org. Retrieved 4 November 2019.
  7. ^ Editors, "Metal Tubes for Receivers", Radio Engineering, April 1935, pp. 18 - 19
  8. ^ G. F. Metcalf, J. E. Beggs, "All-metal receiving tubes, the manufacturing technique", Electronics, May 1935, pp. 149 - 150
  9. ^ Editors, "Making Metal Tubes", Radio Engineering, Sept. 1935, pp. 31, 34
  10. ^ IEC 60067: "Dimensions of electronic tubes and valves. IEC dimensions" (1966). Also published as BS 448-1:1981.
  11. ^ Schmid, Kurt. "R-390A plug-in multi-section electrolytic capacitor kit" (PDF). Schmid-Mainz. Retrieved 20 July 2013.
  12. ^ A socket similar to the standard otcal but with 11 pins also exists, and is also called "octal". It is an industry standard, developed mainly for industrial 3-phase relays (3PDT or TPDT) in order to accommodate three changeover contacts. It was also used in some older power supplies but was never used for tubes.
  13. ^ "Amperite | Time Delay Relays | Flashers | Controlling Devices | Relay Requirements". www.amperite.com. Retrieved 2016-01-22.
  14. ^ Advantages of a Full Featured, Octal 700 Series Relay (PDF). Magnecraft.
  15. ^ Amperite Relay Catalog (PDF). Amperite.
  16. ^ Staff of 'Wireless World' (1958). "Explanation of Valve-Base Connections". Radio Valve Data (Sixth ed.). London: Iliffe $ Sons Ltd. p. 87.
  17. ^ "Sylvania Type 7A8" (PDF). Retrieved 20 July 2013.
  18. ^ "DAC21". Retrieved 25 August 2012.
  19. ^ Photo of 1920s era peanut tube.
  20. ^ a b The National Valve Museum: 6J6
  21. ^ a b Schiffer, Michael Brian (1992). The Portable Radio in American Life. University of Arizona Press. pp. 123–125. ISBN 978-0816512843.
  22. ^ Schematic of RCA Model BP-10
  23. ^ Photo of RCA Model BP-10
  24. ^ "Miniature Radio Tubes" (PDF). Radio Age: 19. April 1945. Retrieved 20 July 2013.
  25. ^ Sylvania Receiving Tubes Technical Manual, 14th Edition
  26. ^ Sōgo Okamura, ed. (1994). History of Electron Tubes. IOS Press. p. 27. ISBN 978-9051991451.
  27. ^ 2C43 data sheet
  28. ^ "Pacific T.V. - Vacuum Tube Sockets".
  29. ^ "Philips Data Handbook: Electron Tubes, Part 4", April 1969l
  30. ^ "Abbildungen - Figures".
  31. ^ "Appendix - Figures". KyteLabs. Retrieved 7 January 2013.
  32. ^ "Pee Wee 3p". Frank Philipse. Retrieved 7 January 2013.
  33. ^ "Base B3G". The National Valve Museum. Retrieved 20 July 2013.
  34. ^ "EA50 Signal Diode". Retrieved 25 May 2014.
  35. ^ "Miniwatt" Technical Data (6th ed.). Australia: The "Miniwatt" Electronics Division of Philips Electrical Industries Pty. Limited. 1958. p. 158.
  36. ^ "A-P_Oscillator". Retrieved 7 January 2013. Saga of the Vacuumtube, Tyne page 176
  37. ^ "Base B4". Retrieved 25 May 2014.
  38. ^ "Base B5". Retrieved 25 May 2014.
  39. ^ "Base UX6". The National Valve Museum.
  40. ^ "Base B7". The national Valve Museum. Retrieved 9 January 2013.
  41. ^ Philipse, Frank. "Frank's Electron tube Pages - Tube Bases". Retrieved 26 May 2014.
  42. ^ a b "Base Mazda Octal". The National Valve Museum. Retrieved 7 January 2013.
  43. ^ a b "ATP4 tube". The AmateurTele.com. Retrieved 10 February 2015.
  44. ^ "Appendix - Figures". KyteLabs.
  45. ^ "Base B8B". The National Valve Museum. Retrieved 8 January 2013.
  46. ^ "Base B9G". Retrieved 25 May 2014.
  47. ^ Dekker, Ronald. "EF50 - The Development of the All-Glass Valve". Retrieved 25 May 2014.
  48. ^ Prakke, F.; J.L.H. Jonker; M.J.O. Strutt (May 1939). "A New "All-Glass" Valve Construction" (PDF). The Wireless Engineer. Retrieved 26 May 2014.
  49. ^ "Novar vs Magnoval Vacuum Tube Sockets". Antique Radio Forums. 2011-02-17.
  50. ^ "Base B10B". The National Valve Museum. Retrieved 7 January 2013.
  51. ^ "PCF201".
  52. ^ KyteLabs (2014-02-19). "KyteLabs InfoBase - Electron Tubes & Valves Data" (in German and English). Table A.4.1 - Sockeltypen - Basing Types. Retrieved 13 October 2014.{{cite web}}: CS1 maint: location (link)
  53. ^ "Nuvistor 13CW4". Tube Data. Retrieved 20 July 2013.

See also

[edit]